• Home
• Digital Scales Address Several Needs

25 Responses to “1/25 Scale Baby Monster truck BigFoot and Grave Digger Part A”

1. rcWizzard on February 28th, 2010 | 11:01 pm

   

   @TheChevyman360
   No.

2. TheChevyman360 on March 7th, 2010 | 2:39 pm

   

   how thick is your music wire

3. rcWizzard on March 7th, 2010 | 11:31 pm

   

   @TheChevyman360
   5/64 inch. .078″

4. TheChevyman360 on March 12th, 2010 | 1:03 am

   

   what kind of rear end did you say it was

5. rcWizzard on March 12th, 2010 | 12:47 pm

   

   @TheChevyman360
   They have to be traced onto wood, like in video part B.

6. TheChevyman360 on March 15th, 2010 | 1:11 am

   

   where do you get your pan car diff

7. rcWizzard on March 15th, 2010 | 3:06 am

   

   @TheChevyman360
   Hobby Hangar in northern VA.

8. TheChevyman360 on March 16th, 2010 | 1:11 am

   

   where did you get your models

9. rcWizzard on March 16th, 2010 | 2:28 am

   

   @TheChevyman360
   A hobby shop, also Walmart.

10. TheChevyman360 on April 10th, 2010 | 1:53 pm

    

    how did you bend your music wire did you use heat or jigs or what so well awsome vids 5stars.

11. rcWizzard on April 10th, 2010 | 3:19 pm

    

    @TheChevyman360
    Most hobby shops have the jig. An aluminum plate with steel pins sticking up, and grooves cut in it. You hold it in a vise. Also, a hand bender, at the area in the hobby shop.

12. TheChevyman360 on April 10th, 2010 | 4:07 pm

    

    @rcWizzard ok so do you think hobby town usa would have them because my local hobby place is hobby lobby and I bet they would not have that so I would have to go to little rock to find them in hobby town usa

13. rcWizzard on April 10th, 2010 | 11:59 pm

    

    @TheChevyman360
    Why don’t you call them and ask?

14. TheChevyman360 on April 12th, 2010 | 12:23 pm

    

    @rcWizzard ya thhats a good idea so is their any special name for them or just jigs.

15. rcWizzard on April 12th, 2010 | 9:55 pm

    

    @TheChevyman360
    Jigs or tube benders.

16. TheChevyman360 on April 13th, 2010 | 1:26 am

    

    did you just sell a bigfoot model on ebay

17. rcWizzard on April 13th, 2010 | 2:22 am

    

    @TheChevyman360
    No, Why???

18. TheChevyman360 on April 18th, 2010 | 4:18 pm

    

    how much would you charge for the baby grave digger full drive system transfer case,rearend,drive shafts,and U-joints and any thing else I would need for the drive system.

19. rcWizzard on April 19th, 2010 | 2:23 am

    

    @TheChevyman360
    It’s not perfected yet. Meaning, I need to, find- create- fabricate bevel gears for the differential. The first set got fried. So, I need to make one for myself, before I make one for someone else. And that’s not going to happen before I finish the 1/4 Scale Grave Digger project. But an estimate would be around $600.00, and that’s 2 wheel drive. Custom stuff is expensive!!

20. TheChevyman360 on April 19th, 2010 | 10:58 pm

    

    what coler blue did you use for bigfoot.

21. rcWizzard on April 20th, 2010 | 2:34 am

    

    @TheChevyman360
    I painted it 10 years ago, I don’t remember.

22. gabe2304 on April 20th, 2010 | 9:24 pm

    

    How did you make this??Would you sell them???

23. rcWizzard on April 21st, 2010 | 2:16 am

    

    @gabe2304
    Watch part B.
    No, not for sale.

24. Joelepp13 on May 6th, 2010 | 1:11 am

    

    How wide are they from the outside of the wheel to the outside of the other wheel

25. rcWizzard on May 6th, 2010 | 9:16 pm

    

    @Joelepp13
    6.75 inches.

Leave a Reply